What is this? So if you are using dry, untreated boards, you will have to install them with a slight gap of about 1/4 in (0.64 cm). This way, the boards will expand over the rest of the humid season and then shrink once the dry seasons arrive, leaving an appropriate gap.

Will decking boards shrink?

Any type of decking board will expand and shrink, whether it’s wood, plastic, or composites. However, the rate of how they change in size and why they do so differs. Wooden decking boards are the most susceptible to shrinking and expanding. When exposed to moisture, they can easily absorb it and swell.

How do I stop my deck boards from shrinking?

You can use a framing nail or a 16D nail to make sure that each board is a uniform distance from each other. However, if you’re building with wet lumber, you should leave boards 1/16” apart, as this lumber will shrink more over time.

Will 5 4 deck boards shrink?

Conclusion of 5/4 decking spacing Ideally, the finish gap between deck boards will be between 1/8″ (3mm) and 5/16″ (8mm) but should not be installed at this spacing as 5/4 boards will shrink, increasing the gap.

How long does it take pressure treated lumber to shrink?

Over time, most treated lumber will shrink slightly across its width as it dries out. Take this small amount of shrinkage into account when laying decking or fence boards. After being outdoors for six to 12 months, treated lumber will develop cracks, called “checks,” along the surface of each board.

Do deck joists shrink?

Board spacing should allow for air circulation and drainage and also take into account seasonal movement. All timber will shrink as the timber dries and swell as it takes on moisture.

How much do deck boards expand?

When installing new air-dried decking the proper gap ranges from 1/8 inch (3.5 mm) – 1/4 inch (6.5mm) depending on the environment.

Should I use deck boards or 2x6?

, but is also more expensive. Spacing between deck boards provide a few critical functions. The primary function is to drain water from the deck. Gaps that are narrow (1/8”), can catch debris, specifically on top of the joists, and can be difficult to clean out.

Does pressure treated deck boards shrink?

Regular pressure treated wood tends to be somewhat wet when it’s new. That means, as it weathers in the sun and the heat, it will dry out some and shrink slightly. … In this case, some space between the boards is a good idea because the wood can actually expand slightly over time.

Does treated wood shrink as Dries?

Even products that are sealed and treated are going to shrink. This most typically occurs across the width of boards, so builders should take into consideration the fact that their lumber will shrink over time. Additionally, as part of the drying stage of treated wood, the boards will crack, also referred to as checks.

Article first time published on

Do cedar deck boards shrink?

First of all, cedar deck boards can shrink and expand depending on how high or low the humidity levels outside are. If it is especially dry outside then cedar wood will contract and shrink and if it is quite wet outside or it the humidity levels are high then cedar deck boards will expand.

Does decking swell wet?

Because decks are outside, they are continuously exposed to changing humidity. During more humid seasons, like summer, decking will soak up more moisture, causing the boards to expand. … A door that might work just fine in the winter may in the summer swell and not close properly in its door frame.

How much will treated decking shrink?

This way, the boards will expand over the rest of the humid season and then shrink once the dry seasons arrive, leaving an appropriate gap. If you’re using pressure-treated boards, you might want to leave a smaller gap of about 1/8 in (0.32 cm).

How much will a treated 2x4 shrink?

There is very little shrinkage along the length of the lumber. The thickness of the 2×4 will change slightly, but not by much. But the width of the 2×4 will experience the greatest shrinkage. It may only measure 3 and 3/8 inches in width.

How long does wood take to shrink?

This may take several years, depending on the type of wood, how it was cut, the weather and humidity in the area where it will be dried. A block of wood or a piece of lumber has three areas: radial, longitudinal and tangential.

Should deck boards have a space between them?

Proper wood deck board spacing should have at least a 1/8 inch gap after the decking has dried out. If you install your wood or treated deck boards while they are still wet boards, then they should be attached without a gap between them.

Why is there a space between deck boards?

The most important reason to have a spacing gap is to allow the boards the room to expand and contract naturally. Wood, by nature, expands and contracts when there are seasonal humidity changes and the wood begins to absorb or expel moisture.

Should I leave a space between deck boards?

When securing the decking, it is important to leave adequate spacing between the boards for water to drain. The goal is to have about an 1/8-inch gap (the diameter of an 8d nail) between boards after the decking has dried to its equilibrium moisture content.

How much will a 2x6 shrink?

For a 2×6, we will see some pieces at 15% MC shrinking 0.22” and some only 0.11” with the others being in between. This is due to grain variation within the wood.

How do you raise deck joists?

Cross-Joist Bracing The best way is to place cross-braces, such as two-by-fours, across the length of the deck on the underside of the joists. Place them perpendicular to the joists so that you can then raise the whole deck at once as necessary.

Can you add joist to existing deck?

If the overall structure of the deck is still in good shape, then yes, you can add new joists between the existing. If there is rot in the existing framing, you’re better off to start from scratch with all new materials.

Does untreated wood shrink?

Conventional wisdom tells us when wood absorbs water it swells and when wood dries it shrinks. But wood will only shrink and swell below its fiber saturation point, which is around 28% moisture content (MC).

How much space should be between deck and house?

A proper connection would have a 1/2” to 3/4” gap between the deck construction and the house to allow rain and meltwater from snow to flush through; this prevents rot from forming in the deck timbers, and/or in the adjacent wood of the house framing.

Should deck boards be installed crown up or down?

Crown up is the preferred installation method, despite the potential for bark side down deck boards to experience shelling. Bark side down allows for the formation of a crown warp. Once the board forms a crown, there’s less potential for the wood to hold water, which could lead to the wood splintering and rotting.

Can you use 1 inch boards for a deck?

Certain tropical hardwoods, like Ipe, for example, are hardier than common pressure-treated woods like cedar or pine. So what size are deck boards made of different types of wood? The standard thickness for all types of wood is 1”, however, for weaker woods, choosing a thicker board can give you a sturdier feel.

Should deck boards overhang fascia?

When installing decking boards, be sure to allow for enough overhang to cover the fascia board and whatever additional amount you prefer. … This means the installed deck boards should have at least 1.75 to 2.75” overhang before the fascia is installed.

Can I use 1x6 for deck boards?

Width of material: We recommend only 1×4, 5/4×4 or narrower boards. Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.

Will wet wood shrink?

Wet wood will shrink as it dries out and is less stable, which can cause it to check and warp.

What happens if you stain pressure treated wood too soon?

If you stain pressure-treated wood too soon, the stain will be unable to fully penetrate the wood, and you will not get the protective benefits of the stain. What is the best stain for pressure-treated wood? An oil-based stain is the best for pressure-treated wood.

Is it OK to cut pressure treated wood?

Sawdust produced by cutting or machining pressure-treated wood is not hazardous to people, plants or pets. When sawing or machining treated wood, wear eye protection, a dust mask and gloves. When you complete a project, clean up all sawdust and debris. … Do not burn treated wood in open fires, stoves or fireplaces.

What happens if deck boards are too close together?

When the deck boards are too close together, water won’t drain properly and air does not circulate. Your deck boards stay wet causing rot and that can lead to structural failure/ wood rot. … The Saw Guide is also perfect for removing old paint and finish between deck boards before refinishing your deck.